Effect of the addition of an inorganic carbon source on the degradation of sotol vinasse by Rhodopseudomonastelluris.

The difficulty of the microbial conversion process for the degradation of sotol vinasse due to its high acidity and organic load makes it an effluent with high potential for environmental contamination, therefore its treatment is of special interest. Calcium carbonate is found in great abundance and has the ability to act as a neutralizing agent, maintaining the alkalinity of the fermentation medium as well as, through its dissociation, releasing CO2 molecules that can be used by phototrophic CO2-fixing bacteria. This study evaluated the use of Rhodopseudomonas telluris (OR069658) for the degradation of vinasse in different concentrations of calcium carbonate (0, 2, 4, 6, 8 and 10% m/v). The results showed that calcium carbonate concentration influenced volatile fatty acids (VFA), alkalinity and pH, which in turn influenced changes in the degradation of chemical oxygen demand (COD), phenol and sulfate. Maximum COD and phenol degradation values of 83.16 ± 0.15% and 90.16 ± 0.30%, respectively, were obtained at a calcium carbonate concentration of 4%. At the same time, the lowest COD and phenol degradation values of 52.01 ± 0.38% and 68.21 ± 0.81%, respectively, were obtained at a calcium carbonate concentration of 0%. The data obtained also revealed to us that at high calcium carbonate concentrations of 6-10%, sotol vinasse can be biosynthesized by Rhodopseudomonas telluris (OR069658) to VFA, facilitating the degradation of sulfates. The findings of this study confirmed the potential for using Rhodopseudomonas telluris (OR069658) at a calcium carbonate concentration of 4% as an appropriate alternative treatment for sotol vinasse degradation.

Changes in phytochemical content, bioaccesibility and antioxidant capacity of corn tortillas during simulated in vitro gastrointestinal digestion.

There is a little information about the effect of corn process conditions on the bioactive compounds of tortillas during gastrointestinal digestion. Tortillas elaborated with traditional and extrusion nixtamalization process were subjected to in vitro digestion. Extracts recovered from digestion were employed to determine the changes in phytochemicals, bioaccesibility and antioxidant capacity (DPPH, ABTS and FRAP). Digestion contributed to a greater solubilization of phenolic compounds in raw corn and tortillas, especially in the intestinal phase (311.4-583.2 mg GAE/100 g). With bioaccessibility indexes of 162.83 to 960.7 %. Intestinal phase affected the content of anthocyanins, reaching a lower bioaccessibility value than the found in undigested samples (17.90-29.91 %). Even though the traditional white tortilla showed the highest bioaccessibility values, blue tortilla showed a higher antioxidant activity in different phases of digestion. Both tortillas could function as prebiotic agents in the large intestine. Corn-based products are valuable as part of a healthy diet.

Milk-Gelling Properties of Proteases Extracted from the Fruits of Solanum Elaeagnifolium Cavanilles.

There is little information on the milk coagulation process by plant proteases combined with chymosins. This work is aimed at studying the capability of protease enclosed in the ripe fruits of Solanum elaeagnifolium (commonly named trompillo) to form milk gels by itself and in combination with chymosin. For this purpose, proteases were partially purified from trompillo fruits. These proteases had a molecular weight of ~60 kDa, and results suggest cucumisin-like serine proteases, though further studies are needed to confirm this observation. Unlike chymosins, trompillo proteases had high proteolytic activity (PA = 50.23 UTyr mg protein-1) and low milk-clotting activity (MCA = 3658.86 SU mL-1). Consequently, the ratio of MCA/PA was lower in trompillo proteases (6.83) than in chymosins (187 to 223). Our result also showed that milk gels formed with trompillo proteases were softer (7.03 mPa s) and had a higher release of whey (31.08%) than the milk gels clotted with chymosin (~10 mPa s and ~4% of syneresis). However, the combination of trompillo proteases with chymosin sped up the gelling process (21 min), improved the firmness of milk gels (12 mPa s), and decreased the whey release from milk curds (3.41%). Therefore, trompillo proteases could be combined with chymosin to improve the cheese yield and change certain cheese features.

Anthocyanins and Functional Compounds Change in a Third-Generation Snacks Prepared Using Extruded Blue Maize, Black Bean, and Chard: An Optimization.

The effect of extrusion cooking on bioactive compounds in third-generation snacks (TGSE) and microwave-expanded snacks (MWSE) prepared using black bean, blue maize, and chard (FBCS) was evaluated. FBCS was extruded at different moisture contents (MC; 22.2-35.7%), extrusion temperatures (ET; 102-142 °C), and screw speeds (SP; 96-171 rpm). Total anthocyanin content (TAC), contents of individual anthocyanins, viz., cyanidin-3-glucoside, malvidin-3-glucoside, pelargonidin-3-glucoside, pelargonidin-3-5-diglucoside, and delphinidin-3-glucoside chloride, total phenolic content (TPC), antioxidant activity (AA), and color parameters were determined. TAC and individual anthocyanin levels increased with the reduction in ET. ET and MC affected the chemical and color properties; increase in ET caused a significant reduction in TPC and AA. Microwave expansion reduced anthocyanin content and AA, and increased TPC. Extrusion under optimal conditions (29% MC, 111 rpm, and 120 °C) generated products with a high retention of functional compounds, with high TAC (41.81%) and TPC (28.23%). Experimental validation of optimized process parameters yielded an average error of 13.73% from the predicted contents of individual anthocyanins. Results suggest that the TGSE of FBCS obtained by combining extrusion and microwave expansion achieved significant retention of bioactive compounds having potential physiological benefits for humans.

Optimisation of the ultrasound-assisted extraction of betalains and polyphenols from Amaranthus hypochondriacus var. Nutrisol.

The present study optimised the ultrasound-assisted extraction (UAE) of bioactive compounds from Amaranthus hypochondriacus var. Nutrisol. Influence of temperature (25.86-54.14 °C) and ultrasonic power densities (UPD) (76.01-273.99 mW/mL) on total betalains (BT), betacyanins (BC), betaxanthins (BX), total polyphenols (TP), antioxidant activity (AA), colour parameters (L*, a*, and b*), amaranthine (A), and isoamaranthine (IA) were evaluated using response surface methodology. Moreover, betalain extraction kinetics and mass transfer coefficients (KLa) were determined for each experimental condition. BT, BC, BX, TP, AA, b*, KLa, and A were significantly affected (p < 0.05) by temperature extraction and UPD, whereas L*, a*, and IA were only affected (p < 0.05) by temperature. All response models were significantly validated with regression coefficients (R2) ranging from 87.46 to 99.29%. BT, A, IA, and KLa in UAE were 1.38, 1.65, 1.50, and 29.93 times higher than determined using conventional extraction, respectively. Optimal UAE conditions were obtained at 41.80 °C and 188.84 mW/mL using the desired function methodology. Under these conditions, the experimental values for BC, BX, BT, TP, AA, L*, a*, b*, KLa, A, and IA were closely related to the predicted values, indicating the suitability of the developed quadratic models. This study proposes a simple and efficient UAE method to obtain betalains and polyphenols with high antioxidant activity, which can be used in several applications within the food industry.

The Effect of Nixtamalization Extrusion Process and Tortillas Making on the Stability of Anthocyanins from Blue Corn through the Kinetic and Thermodynamic Parameters.

The blue corn-based products are considered functional foods due to their high concentration of anthocyanins. The aim of this study was to estimate the kinetic and thermodynamic parameters of the thermal degradation of anthocyanins from extruded nixtamalized corn products. A comparative study of anthocyanins thermal stability in these matrices in a buffer solution (pH 2.5) was investigated at different temperatures (60, 75 or 90 °C). Results showed the mechanism of anthocyanins degradation followed first-order reaction kinetics. The values of the reaction rate constant (k) were found to be in a range of 0.027-0.037 h-1 at 60 °C, 0.107-0.113 h-1 at 75 °C and 0.340-0.354 h-1 at 90 °C. The higher the k value was, the shorter the half-life time and D-value. The activation energy (Ea) and z-values were in the range of 75.1-89.2 kJ/mol and 28.8-35.1 °C, respectively. The coefficient Q10 indicated the reaction rate approximately doubles with every 10 °C temperature increase. ∆H, ∆S and ∆G indicated the degradation of anthocyanins was an endothermic and nonspontaneous reaction. Even the major susceptibility of the anthocyanins in extruded nixtamalized corn products at the time-temperature combination applied, there was not difference between flour and tortilla, this imply that most of the anthocyanins were degraded during the nixtamalization extrusion process and no significative further degradation occur in the cooking step. This study provides and advance in the knowledge on the effect of nixtamalization extrusion process and tortillas making on the stability of anthocyanins from blue corn. However, further studies are needed.

Effect of ultrasound and steam treatments on bioaccessibility of ß-carotene and physicochemical parameters in orange-fleshed sweet potato juice.

Several health benefits have been associated to orange-fleshed sweet potato owing to the existence of various bioactive compounds, including ß-carotene. The purpose of this study was to establish the effect of ultrasound and steam treatment on the bioaccessibility of ß-carotene, total polyphenols, antioxidant activity, polyphenol oxidase, peroxidase activity, and color in the orange-fleshed sweet potato juice. Sweet potato juice was processed using ultrasound (0.66 W cm-2 and 8 min), steam (2 min), and a combination of steam and ultrasound. The bioaccessibility of ß-carotene was increased in processed sweet potato juice, with samples treated by ultrasound showing the highest bioaccessibility (76.6%). Processing had no effect on antioxidant or enzyme activity, but resulted in significant changes in the color of the juice. As a processing technology, ultrasound enables preservation or improvement of the quality of sweet potato juice, and when conbined with other treatments, facilitates the development of new products.

Mexican oregano essential oils as alternatives to butylated hydroxytoluene to improve the shelf life of ground beef.

Oregano essential oils from Lippia berlandieri Schauer (Lb) and Poliomintha longiflora Gray (Pl) were tested against the antioxidant butylated hydroxytoluene (Bht) to evaluate effects on the shelf life of ground beef (GB) over 7 days of storage at 4°C. The treatments were GB1 = GB control, GB2 = GB +100 mg/kg of Bht, GB3 = GB +100 mg/kg of Lb, and GB4 = GB +100 mg/kg of Pl. Lightness, redness, hardness, and springiness showed differences (p < .05) between treatments and days interaction, which serve as indicators of ground beef preserved quality and consumer acceptance. Mesophilic, psychrophilic, and lactic acid bacteria numbers and antioxidant activity showed differences (p < .05) for treatments and days. Sensory attributes showed no differences between treatments. The oregano oils may provide extended shelf life for packaged meat products treated with these natural additives and hence may be used for ground beef preservation.

Continuous Flow UV-C Irradiation Effects on the Physicochemical Properties of Aloe vera Gel and Pitaya (Stenocereus spp.) Blend.

Physicochemical properties of a blend of 10% Aloe vera gel with 5% pitaya juice subjected to UV-C doses of 16.5, 27.7, and 40 mJ/cm2 were evaluated at pH 3.5 and 5.5. Unprocessed treatments were used as the control. The a* color parameter decreased and luminosity increased at pH 3.5. The decrease in the reddish color was consistent with the decrease in total betalains content and stabilized at pH 5.5. The NMR analyses of UV-C treatments showed changes in betalains signal patterns. Polyphenolics content was significantly reduced in the UV-C treatments at pH 5.5. UV-C processing decreased the antioxidant activity 1.25 times compared to unprocessed treatments. Total sugar content was reduced as the UV-C dose increased. Doses above 16.5 mJ/cm2 resulted in a higher simple sugar content at a pH 3.5. The UV-C continuous flow technology can be applied to stabilize betalains in Aloe vera-pitaya blends at a UV-C dose of 16.5 mJ/cm2 and pH 5.5.

Effect of extrusion conditions on the anthocyanin content, functionality, and pasting properties of obtained nixtamalized blue corn flour (Zea mays L.) and process optimization.

The aim of this study was to evaluate the effect of extrusion factors on the properties of extruded nixtamalized corn flours (ENCFs), determine the optimal conditions, and produce a tortilla with texture and nutraceutical characteristics acceptable for consumers. The processing factors used were feed moisture (FM, 15 to 30%), extruder temperature (T, 70 to 110 °C), and screw speed (SS, 50 to 145 rpm). The properties evaluated in the flours were total anthocyanins (TA), subjective water absorption capacity, and peak viscosity (PV). Response surface methodology and analysis of variance were used in the evaluation. The linear and quadratic terms of FM had a greater effect on all evaluated parameters. The optimization was performed using the numerical method of global desirability. The response variables that were optimized in the ENCF were TAs (maximize) and PV (maximize). The optimal region was the following: FM (18.17%), T (92.03 °C), and SS (76.61 rpm). The experimental value for the TA in the optimized ENCF was 226.07 mg/kg, and the PV was 1063.9 cP. The results of this study could help develop nixtamalized corn flours with desirable characteristics to make tortillas using the extrusion process. PRACTICAL APPLICATION: The results obtained would be useful for the tortilla industry, developing nixtamalized corn flours with desirable characteristics to make healthy tortillas using the extrusion process, with minimum losses in biologically active compounds such as anthocyanins (health promoters) without affect negatively the eating quality of the product (good texture).

Physicochemical, Rheological, and Morphological Characteristics of Products from Traditional and Extrusion Nixtamalization Processes and Their Relation to Starch.

The aim of this study was to compare the physicochemical, rheological, and morphological characteristics of corn, nixtamalized flour, masa, and tortillas from the traditional nixtamalization process (TNP) and the extrusion nixtamalization process (ENP) and their relationship with starch. The traditional and extrusion processes were carried out using the same variety of corn. From both processes, samples of ground corn, nixtamalized flour, masa, and tortillas were obtained. The extrusion process produced corn flour with particle sizes smaller (particle size index, PSI = 51) than that of flour produced by the traditional nixtamalization process (PSI = 44). Masa from the TNP showed higher modulus of elasticity (G') and viscosity (G ″) values than that off masa from the ENP. Furthermore, in a temperature sweep test, masa from the TNP showed a peak in G' and G ″, while the masa from the ENP did not display these peaks. The ENP-produced tortillas had higher resistant starch contents and comparable firmness and rollability to those from the TNP but lower quality parameter values. A comparison of the products' physicochemical properties obtained by the two processes shows the importance of controlling the damage to starch during the milling and extrusion processes to obtain tortillas of better quality. For the first time, we propose the measurement of the viscoelastic parameters G' and G ″ in temperature sweep mode to monitor changes in the degree of starch damage.

Effects of UV-C irradiation and traditional thermal processing on acemannan contained in Aloe vera gel blends.

The effects of pH (3.5, 4.5, and 5.5) and UV-C irradiation dose (12.8, 24.2, 35.8, and 54.6 mJ/cm2) on the physicochemical properties changes in 10% Aloe vera gel blends; in addition, the acemannan concentration and structural changes in the precipitated polysaccharides were evaluated. A thermal treatment (TT; 45 s at 90 °C) was used for comparison. In contrast to TT, a dose of 24.2 mJ/cm2 did not induce significant changes of free sugar content. Moreover, TT and UV-C irradiation did not significantly affect the content of mannose but increased those of galactose, fructose, and glucose. 1H NMR analysis revealed minimal changes in the isolated fractions of acemannan, indicating that compared to the unprocessed control sample, the acemannan deacetylation was more pronounced by TT (27%) than by UV-C irradiation (11% at 54.6 mJ/cm2), without any significant difference between the two. UV-C irradiation of Aloe vera gel blends at pH 3.5 and 24.2 mJ/cm2 was an alternative to TT and efficiently preserve the characteristics of acemannan.

Effect of Agave Fructans as Carrier on the Encapsulation of Blue Corn Anthocyanins by Spray Drying.

Effects of agave fructans as carrier agents on the encapsulation of blue corn anthocyanins using spray-drying were evaluated. Blue corn extract was mixed with 6%, 8%, 10%, and 12% (w/v) of agave fructans in duplicate and dried at 150 °C. The extract showed good contents of anthocyanins, polyphenols, and antioxidant activity. The increase of agave fructans in the encapsulated powders caused a significant increase (p < 0.05) in the humidity, water activity (aw), pH, bulk density, water solubility index (WSI), and color L* values. On the contrary, the agave fructan addition decreased the hygroscopicity, water absorption index (WAI), antioxidant activity, total anthocyanin, total polyphenol, and individual anthocyanin contents. The encapsulation of blue corn extract with 6% agave fructans (w/v) resulted in good physical, thermal, morphological, and high antioxidant properties. The results suggest that the use of agave fructans as wall material represents advantages in the conservation of anthocyanins and other bioactive compounds from blue corn extract during their encapsulation. The application of blue corn anthocyanin encapsulated powders as a food ingredient is promising for food pigmentation, representing additional advantages for their contribution as a soluble fiber that can benefit the health of consumers.

Inhibitory effect of saccharides and phenolic compounds from maize silks on intestinal α-glucosidases.

Maize silks have been used in Mexico for centuries as a natural-based treatment for various illnesses, including obesity and diabetes. It has been shown in mice that intake of maize silk extracts reduces the levels of blood glucose. However, it is not clear how or what maize silk compounds are involved in such an effect. A hypothesized mechanism is that some maize silk compounds can inhibit carbohydrate hydrolyzing enzymes like α-glucosidases. This work aimed to assess the capability of both saccharides and phenolic compounds from maize silks to inhibit intestinal α-glucosidases. Results showed that saccharides from maize silks did not produce inhibition on intestinal α-glucosidases, but phenolics did. Maize silk phenolics increased the value of Km significantly and decreased the Vmax slightly, indicating a mixed inhibition of α-glucosidases. According to the molecular docking analysis, the phenolics maysin, methoxymaysin, and apimaysin, which had the highest predicted binding energies, could be responsible for the inhibition of α-glucosidases. PRACTICAL APPLICATIONS: The International Diabetes Federation (IDF) reported in 2017 that diabetes affects over 424 million people worldwide, and caused 4 million deaths. Non-insulin-dependent diabetes or type 2 diabetes mellitus (T2DM) accounts for ∼90% of cases. T2DM is characterized by insulin resistance and pancreatic ß-cell failure. Therapy for T2DM includes the use of sulfonylureas, thiazolidinediones, biguanides, and α-glucosidase inhibitors. Regarding the α-glucosidase inhibitors, only few are commercially available, and these have been associated with severe gastrointestinal side effects. This work aimed to assess the capability of both saccharides and phenolic compounds from maize silks to inhibit intestinal α-glucosidases. Results from this work evidenced that maize silk polyphenols acted as effective inhibitors of intestinal rat α-glucosidases. Computational analysis of maize silk polyphenols indicated that maysin, a particular flavonoid from maize silks, could be responsible for the inhibition of α-glucosidases.

Effects of the Addition of Flaxseed and Amaranth on the Physicochemical and Functional Properties of Instant-Extruded Products.

The addition of flaxseed and amaranth on the physicochemical, functional, and microstructural changes of instant-extruded products was evaluated. Six mixtures with different proportions of amaranth (18.7-33.1%), flaxseed (6.6-9.3%), maize grits (55.6-67.3%) and minor ingredients (4.7%) were extruded in a twin-screw extruder. Insoluble and soluble fiber contents in extrudates increased as the proportions of amaranth and flaxseed increased. However, the highest flaxseed proportion had the highest soluble fiber content (1.9%). Extruded products with the highest proportion of flaxseed and amaranth resulted in the highest dietary fiber content and hardness values (5.2 N), which was correlated with the microstructural analysis where the crystallinity increased, resulting in larger, and more compact laminar structure. The extruded products with the highest maize grits proportion had the highest viscosity, expansion, and water absorption indexes, and the lowest water solubility index values. The mixtures with amaranth (18.7-22.9%), flaxseed (8.6-9.3%), and maize grits (63.8-67.3%) resulted in extruded products with acceptable physicochemical and functional properties.

Improving Cull Cow Meat Quality Using Vacuum Impregnation.

Boneless strip loins from mature cows (50 to 70 months of age) were vacuum impregnated (VI) with an isotonic solution (IS) of sodium chloride. This study sought to determine the vacuum impregnation and microstructural properties of meat from cull cows. The experiments were conducted by varying the pressure, p 1 (20.3, 71.1 kPa), and time, t 1 (0.5, 2.0, 4.0 h), of impregnation. After the VI step, the meat was kept for a time, t 2 (0.0, 0.5, 2.0, 4.0 h), in the IS under atmospheric pressure. The microstructural changes, impregnation, deformation, and porosity of the meat were measured in all the treatments. Impregnation and deformation levels in terms of volume fractions of the initial sample at the end of the vacuum step and the VI processes were calculated according to the mathematical model for deformation-relaxation and hydrodynamic mechanisms. Scanning electron microscopy (SEM) was used to study the microstructure of the vacuum-impregnated meat samples. Results showed that both the vacuum and atmospheric pressures generated a positive impregnation and deformation. The highest values of impregnation X (10.5%) and deformation γ (9.3%) were obtained at p 1 of 71.1 kPa and t 1 of 4.0 h. The sample effective porosity ( ε e ) exhibited a significant interaction (p < 0.01) between p 1 × t 1 . The highest ε e (14.0%) was achieved at p 1 of 20.3 kPa and t 1 of 4.0 h, whereas the most extended distension of meat fibers (98 μm) was observed at the highest levels of p1, t1, and t2. These results indicate that meat from mature cows can undergo a vacuum-wetting process successfully, with an IS of sodium chloride to improve its quality.

Cell wall damage and oxidative stress in Candida albicans ATCC10231 and Aspergillus niger caused by palladium nanoparticles.

In this work the toxic effect of Palladium nanoparticles (PdNPs) was investigated in two eukaryotic cell models, Candida albicans and Aspergillus niger. PdNPs were synthesized by chemical reduction method, obtaining spherical NPs with a primary size ranging from 3 to 15 nm. PdNPs showed a hydrodynamic size of 1548 nm in Lee's minimum media. Minimal inhibitory concentration was determined at 200 and 250 ppm for Candida albicans and Aspergillus niger respectively, revealing a significant cell growth inhibition (ANOVA and tukey analysis, α = 0.5). Reactive Oxygen Species levels were increased in both microorganisms. Confocal, scanning and transmission electron microscopy studies revealed cell wall damage and cellular morphology changes, induced by the interaction of PdNPs, in both microorganisms.

Physicochemical Changes and Resistant-Starch Content of Extruded Cornstarch with and without Storage at Refrigerator Temperatures.

Effects of extrusion cooking and low-temperature storage on the physicochemical changes and resistant starch (RS) content in cornstarch were evaluated. The cornstarch was conditioned at 20%-40% moisture contents and extruded in the range 90-130 °C and at screw speeds in the range 200-360 rpm. The extrudates were stored at 4 °C for 120 h and then at room temperature. The water absorption, solubility index, RS content, viscoelastic, thermal, and microstructural properties of the extrudates were evaluated before and after storage. The extrusion temperature and moisture content significantly affected the physicochemical properties of the extrudates before and after storage. The RS content increased with increasing moisture content and extrusion temperature, and the viscoelastic and thermal properties showed related behaviors. Microscopic analysis showed that extrusion cooking damaged the native starch structure, producing gelatinization and retrogradation and forming RS. The starch containing 35% moisture and extruded at 120 °C and 320 rpm produced the most RS (1.13 g/100 g) after to storage at low temperature. Although the RS formation was low, the results suggest that extrusion cooking could be advantageous for RS production and application in the food industry since it is a pollution less, continuous process requiring only a short residence time.

Effect of extrusion cooking on bioactive compounds in encapsulated red cactus pear powder.

Red cactus pear has significant antioxidant activity and potential as a colorant in food, due to the presence of betalains. However, the betalains are highly thermolabile, and their application in thermal process, as extrusion cooking, should be evaluated. The aim of this study was to evaluate the effect of extrusion conditions on the chemical components of red cactus pear encapsulated powder. Cornstarch and encapsulated powder (2.5% w/w) were mixed and processed by extrusion at different barrel temperatures (80, 100, 120, 140 °C) and screw speeds (225, 275, 325 rpm) using a twin-screw extruder. Mean residence time (trm), color (L*, a*, b*), antioxidant activity, total polyphenol, betacyanin, and betaxanthin contents were determined on extrudates, and pigment degradation reaction rate constants (k) and activation energies (Ea) were calculated. Increases in barrel temperature and screw speed decreased the trm, and this was associated with better retentions of antioxidant activity, total polyphenol, betalain contents. The betacyanins k values ranged the -0.0188 to -0.0206/s and for betaxanthins ranged of -0.0122 to -0.0167/s, while Ea values were 1.5888 to 6.1815 kJ/mol, respectively. The bioactive compounds retention suggests that encapsulated powder can be used as pigments and to provide antioxidant properties to extruded products.

Effect of different calcium sources on the bioactive compounds stability of extruded and nixtamalized blue maize flours.

The stability of antioxidants in extruded and nixtamalized blue maize flours with calcium hydroxide [Ca(OH)2] and calcium lactate [C6H10O6Ca] were evaluated. Extruded blue maize flours batches were obtained by mixing blue maize flours separately with different Ca(OH)2 (0.1, 0.2 and 0.3 %) and C6H10O6Ca (0.3, 0.6 and 0.9 %) concentrations respectively and extruded to obtain the extruded flours. For nixtamalized flours, the maize grains were cooked at 1 % Ca(OH)2 and 2.95 % C6H10O6Ca concentrations respectively. Color, antioxidant activity, total phenolics, total anthocyanins and individual anthocyanins, contents were analyzed. Color, antioxidant activity, anthocyanins contents and total phenolics decreased as the calcium hydroxide concentration increased. In contrast, increasing the calcium lactate concentration on the extruded flours had the opposite effect. The extrusion process retained 57-47 %, 72-62 % and 79-65 % of the anthocyanins content, total phenolic content and antioxidant activity, respectively. These retention rates were higher than those of the nixtamalized flours using the same calcium sources. Cyanidin-3-glucoside and pelargonidin-3-glucoside were identified in the maize kernel and flours. Cyanidin-3-glucoside concentration was increased by both extrusion and nixtamalization processed with either of the two calcium sources. In contrast, pelargonidin-3-glucoside concentration decreased by both processes. Other anthocyanins were observed, but they were not identified.